455 cut and threaded to 16.5”, front sight retained and reinstalled. Area 419 30 MOA base, Vortex medium rings and an Arken SH-4J to top it off. Dead Air Mask muffler. Hollywood quiet and deadly accurate! I usually plink with Norma Tac 22 and run SK long range match when I get serious.
I decided to get an Acculite 17HM2 barrel for my CZ. First box of ammo had me thinking I had an issue with my scope or bad barrel. Had 3-4" inch groups at 25 yards with CCI 17 grain. Cleaned it after 25 rounds, no improvement with the same ammo. Switched the Hornaday 15.5 grain and started getting a single ragged hole, then tried the Hornaday 17 grain, which opened the groups up a little, but still acceptable for a squirrel gun. I shot a couple quick groups at 100 yards with the Hornaday and both weights shot well. Anyone else seen a 17HM2 this picky with ammo? I am wondering if I just had a bad box of ammo. Pic is before the barrel and scope change.
So I picked up this beautiful Cz 452 in 17hm2 for 270 after tax I was wondering if that was a reasonable price and what ammo I should run/have yall had best with.
The DDG Gen Five is an American designed and produced platform based on the physical footprint of the CZ457, so it's a drop-in to factory and aftermarket stocks and chassis systems and accepts factory and aftermarket triggers, magazines and bottom metal.
I'm also nearly finished with my own 457 compatible magazine and bottom metal that will be cross compatible to the factory 457.
The DDG Gen Five is available in two versions, the Standard and Match. The Standard is a single lug lock-up and the Match is a two-lug lock-up, along the lines of the Anschutz 54.
The Receiver is full round, threaded, made from 416SS and uses one of five available MilStd 1913 rails from 0 to 50 MOA. There's also an available 11mm Base Set. The MilStd Rail and 11mm Base Set are secured with four, #8-40 EGW Profile screws and two .125 dowel pins handle shear forces (certainly not from recoil).
The Bolt Assembly features upgraded extraction, improved fire control and the opening and closing cams use timed helices that interface with the helices in the receiver. Of course, the CZ457 is a rock star at feeding/cycling, and that's maintained in the Gen Five platforms.
The Gen Five Standard is a Repeater only and available in RBRP, RBLP, LBLP and LBRP. The Gen Five Match is available as a Repeater and Single Shot and available in the same hand and port configurations.
I have prototyped the Receiver in the early design phase (pictured below) and tested with a factory 457 bolt assembly, and now in the early throes of production, starting with the Gen Five Match. I'm projecting availability to the public within the next five months.
In the attached SolidWorks rendering, the above four actions are the Standard and the lower four are the Match.
The above info answers the questions I've been receiving, but if there are additional questions, feel free to reach out.
Hey Folks! Looking to get into competitive shooting and wanted to get a protektor rear bag. Anyone have any experience with these on the At-One stock and which would fit best? Thanks! Also, any recommendations for front rest?
I bought this beautiful rifle in 2020 but I was today years old when I finally noticed the very subtle inscription in the forearm that reads CZ 457 Match Target Rifle!
Previously I noted the barrel with the 22LR Match inscription and the stock with Varmint MTR, but I’ve never noticed the forearm inscription as it’s very hard to read on mine.
This gun has been a laser beam and I only shoot for fun so I can’t bring myself to replace the stock for a MDT Chassis.
Looking to get into 22 target shooting and while initially leaning toward the varmint LH I have been gushing over the 457 Lux. I have a major hard-on for bolt actions with good iron sights. I was ready to order but noticed the stock is carved with a cheek pad for a righty.
Anyone have experience shooting this lefty? My chief concerns are achieving proper cheek weld and comfort.
I purchased a CZ 457 Varmint Synthetic for a good price on eGun. It came with a 25 MOA Picatinny rail. I also managed to get a Burris SIX Xe 3-18x56 FFP SCR 2 on sale. Unfortunately, I haven’t received anything yet besides the scope, so I can’t measure it. I still need rings or a mounting block to attach the scope. Now I’m unsure how high the mount needs to be.
I’m considering getting a 17hmr barrel to use for night hunting (thermal). Has anyone tried the lothar-walther 17hmr or lija 17hmr barrel? I’m not seeing many options for 17hmr threaded barrels.
Hey I've got an old 455 I haven't done much but put a heavy barrel on. Does anyone know if there are any drum mags, anything more than 10 rounders, that will fit?
Acquired July 23 she started as a stock Pro Varmint and the rabbit hole began.
2nd Gen dawned an Arken scope.
Between 2nd and 3rd Gen she was sit into an KRG Bravo and also had a Petes Pillars MTR Barrell which shoot great and for the price point you couldnt beat it.
Gen 3 was a result of that Rabbit hole going deeper with the addition of an Athlon Midas Tac 5x25x56 as well as the 21 inch Lilja 900 straight barrell...which shoots awesome. I also installed a JARD trigger (3 to 6 oz) and she runs at about 3-1/2 oz.
Gen 4 and to finish her up I added a Harrells tuner, Protektor rear bag 13B (I think) and invested into a better benchrest bipod, the Sinclair F-Class.
I originally wanted to dabble in PRS (I still can) but I found Benchrest to suit me much better. I have been shooting regular local matches as well as a more challenging (much better shooters than I) bi-Monday night benchrest league.
I am bored today so I figure might as well post something we all can relax and eat popcorn to...
Are you a pusher or a puller? Why?
Its true, all of us have been there, done that, and finally decided to join one side or the other. Me personally, I am a puller. Always have been. I tried the pusher mentality but I felt I would end up doing more harm than good even with the bore guide.
Some will say that if you are a puller, you may damage the crown...sure if you are in a hurry and not careful or have the right tools for the job. Once I stepped into the CZ Rimfire world I learned quickly that I had to buy the right tools for the job since CZ rimfire barrels are typically a little tighter than the standard barrels.
So without making this another cleaning thread, since all of us have our own way, are you a Pusher or are you a Puller?