r/CNC • • 1h ago

SHOWCASE These parts are made by #cnc machining with 6061-T6 aluminum. The surface is very clean and even, and those flat areas and circles came out beautifully.

0 Upvotes

#cncmachining isn’t always the right choice, but for parts with regular geometry like this, it’s definitely one of the best options.

The only small downside? 😂 Since CNC is subtractive #manufacturing , some material has to be removed during the process.

Anyway... let’s just enjoy these satisfying details. 🤩


r/CNC • • 2h ago

SHOWCASE Another new zero point work holding idea. Except this one has a point!

Thumbnail gallery
1 Upvotes

r/CNC • • 6h ago

SHOWCASE Machining a 150 mm Sun Wukong figure on a 5-axis CNC

67 Upvotes

This is a small metal Sun Wukong figure we recently machined using a 5-axis CNC.

Despite being only around 200 mm tall, it involved quite a bit of work. Rough machining took about 1.5 hours, while finishing took roughly 20 hours to bring out the smaller details and surface contours.

One of the biggest challenges was tool access around the complex curves and narrow recessed areas. Getting those details right without unnecessary setups took some planning.

Sharing a short video of the machining process.


r/CNC • • 10h ago

OPERATION SUPPORT Moving from Mastercam to NX CAM – Need some guidance understanding RCS

Thumbnail reddit.com
1 Upvotes

r/CNC • • 11h ago

SOFTWARE SUPPORT Has anyone here self-taught hyperMILL?

Thumbnail reddit.com
2 Upvotes

r/CNC • • 17h ago

ROUTER DIY CNC

Post image
6 Upvotes

I'm giving myself the next year to try and create a CNC router (In CAD at least, if i can work out enough there it might get built). Design for the frame comes from a fair bit of shop sabre influence but includes a bit more support structure and room on the front for the vertical table I've always wanted. Onshape is estimating it at 2,200lbs at the moment. Whole thing is 6x12 1/2" wall steel tube. 1/2" end caps on everything to seal up the tube ends. No diagonal bracing yet, unsure if it's needed for a router like this.

Open to suggestions.

Plan is 48x48 cut area plus a vertical table. 12" gantry clearance. Want something very accurate and sturdy/easy to work on. No frills, stuff is easily accessible.


r/CNC • • 1d ago

SOFTWARE SUPPORT Baileigh WR-84V software/post processor recommendations

3 Upvotes

Hello,

A local makerspace was donated a Baileigh WR-84V, however with no software, information what to use, etc.. and I figure I’d help.

I would like to know what software best fits the Baileigh WR-84V cnc router. Specifically trying to figure out the post processor to use, since it’s ran via flash drive.

I am currently using vcarve with my hobby machine. I did some research, and turns out the Baileigh cnc runs a Weihong NK105 controller, which uses NCStudio architecture.

I came across the list of post processors in VCarve, and what is listed for ncstudio.

NC Studio ATC Arcs (inch) (*.nc)
NC Studio ATC Arcs (mm) (*.nc)
NC Studio CC ATC Arcs (INCHES) (*.nc)
NC Studio CC ATC Arcs (mm) (*.nc)

What’s the difference and what one should I use?

To note, this machine does not have the automatic tool changing feature if that makes any difference.

Thank you!


r/CNC • • 1d ago

SALES Northeast US Seeking CNC Partner Snowmaking Project

Post image
16 Upvotes

Hey everyone I’ve been researching for about a year and still haven’t found a shop able to work with me on one offs that then lead to production work. If anyone in the Northeast US is willing to take on a project I’d love to connect with you. Im working towards my own CNC mill but that’s a ways out.

Use is snowmaking, pretty interesting please reach out. Already have a number of prototypes in hand now I just need someone willing to help me hone it in.


r/CNC • • 1d ago

Programmer Hiring a CNC Manufacturing Technician II for space start up in Los Angeles!

Thumbnail
reddit.com
0 Upvotes

Just sharing


r/CNC • • 1d ago

LASER LVD Strippit AXEL 3015L CO2 laser

Post image
1 Upvotes

Kind of feels like a bit of a long shot but does anyone here know anything about CO2 lasers (preferably this specific one) or know anyone who might be knowledgeable about them? Bought and sat for a while, now I'm trying to install and turn it on but I don't know anything about lasers and the support I had was lost during covid. Any help would be appreciated, thank you.


r/CNC • • 1d ago

GENERAL SUPPORT Online resources for learning CNC machining?

8 Upvotes

Does anyone have recommendations for websites or maybe YouTube channels that go in depth on teaching the operations of CNC mills and lathes? I have access to one of each and want to expand my knowledge as far as setup and actually running parts.


r/CNC • • 1d ago

ADVICE Help to Begin Manufacturing with Aluminum

Post image
5 Upvotes

Hi, I have been working on an electronics product for some time, and will be launching it soon. I am working on the final integration of the enclosure design, electronics, etc.

It is currently a low volume product that I am marketing through social media and planning to manufacture through small scale methods like 3d printing and laser cutting.

Today I conducted certain heat testing for my electronics inside of my enclosure for the first time, and it did significantly worse (obviously because it is surrounded by plastic).

I have been interested in an Aluminum based design for some time, being inspired by designs from Teenage Engineering, Apple, etc.

So far, I know little about metal based manufacturing, finishing techniques, etc.

I know there are other ways to make my current plastic based design work, but I am strongly interested in CNC or general machining based manufacturing and would like to understand the tradeoffs for choosing it instead.

I have been looking into websites like JLC CNC and other online quote providers but I'm not satisfied with the online quotes provided by any of them. It seems that they are much more expensive than I would expect them to be. This also applies to 3d printing - JLC 3DP for example shows quotes WAY higher than it costs me to print with my 3d printer.

I'd like to get a general understanding of what is the ideal way to manufacture the enclosure in metal and what cost and design aesthetics would be possible.

Below is an image of the current 3d printed design with ribs, bosses, etc. I've made a simpler .step file which does not have ribs, and uploading that below as well. It would be a great help if you could guide me on this further.

Description of my current 3d printed design: It takes roughly 2 hours and 80gms to print with PLA but that is after I have increased thickness to 2mm and added ribs for extra thickness.

Link to .stl file: https://drive.google.com/file/d/15a2lV3zooDJ1G_MlmgyErOC28VVEwCvG/view?usp=sharing

Apologies if I have posted into the wrong subreddit. If so, let me know which one would be more appropos


r/CNC • • 1d ago

ADVICE recommendation for CNC machine for making clock gears

0 Upvotes

Im planning on going into carpentry but I would also like to make clocks. I currently work for a clock repair company so I know how they work and I could make them by hand but I would like to automate the process a little with a cnc so I can spent more time on the woodworking side of things. My plan is to recreate historic mechanisms and build the cases for them as well. what CNC in the 1000 to 5000 dollar range and what attachments would best be able to cut the fine intricate teeth from brass plates. I'm also looking for something user friendly because I don't really have any experience with CNC machines. Thanks to any responses.


r/CNC • • 1d ago

ADVICE Help with electrical issue

1 Upvotes

Hey all,

So I have aquired an EMCO Concept turn 55(2004 model) from my old school.

I managed to get the software for it off EMCO so all good on that front.

Problem lies with the machine itself, some fun electrical issues.

When I try to power on/ use the machine it trips a ground fault. Sometimes instantly, sometimes after a while of running it.

So far happened about 5 times where it's tripped my ground fault breaker TYPE AC (30mA)

What the machine was doing when it tripped each time.

  1. I was simply opening and closing the door of the machine a few times until it tripped the fault(the door is connected to the EStop circuit)

  2. Ran the spindle briefly at 2k RPM which is the machines max then after some time it tripped.

  3. Stalled the spindle once of course hit the estop before anything happened, then when I disengaged the estop it tripped.

  4. Ran the machine at 1.5k RPM for a few minutes and then it tripped, turned it back on after and worked fine

  5. Tried turning it on and instantly tripped.

I though I found the issue before the 4th time, A small bit of frayed shielding was contacting between the ground and one of the phases in the motor electrical box. All was fine and well. Until it tripped after the 1.5k rpm.

I know the issue lies somewhere with the VFD or Motor as when I have the VFD disconnected all is fine, machine powers on.

What I've done so far.

I have tested the motor windings for any sort of faults etc.

I have take apart the VFD and tested every component I could get my multimeter on and component tester.

I have a feeling it might be that I have the wrong type of breaker, but I want to rule out every other possiblity before getting an electrician out to swap it out for a different type.

Any and all suggestions welcome, let me know if I have left out any information needed

Thanks,


r/CNC • • 2d ago

SOFTWARE Ten models, five ways to build them: what Lamina does

1 Upvotes

I made this! It also does plywood on a router, with relief on the slot corners for your bit. Free and open source, and I am around to answer questions.


r/CNC • • 2d ago

ADVICE How to fix the flared ends on sharp inside corners. Used v carve to set up the cut.

Post image
7 Upvotes

r/CNC • • 2d ago

SOFTWARE SUPPORT Elucad and Elumatec advice

2 Upvotes

I'm wondering if anyone out there has experience with Elucad and Elumatec SBZ profile centers. I've been at door/window manufacturing shop, and there are two SBZ122.71 machines that I jump between. Each of them have their quirks, but I'm fairly familiar with them now. I also program them using Elucad on pc. I've been using the software for about 6 months, but, it has all been hands on learning, no formal instruction on either the software or the machines. The issues I'm coming up against all concern Work flow. The machines are not networked, so files are moved about with USB dongles, so that is a major headache. The second problem is the creation of programs on a per job basis. Each assembly of each job is programmed as a new part. We do have macros, but they are a jumbled mess, with multiple copies, ambiguous file names, multiple redundant folders, no descriptions of what they correspond to, and non uniform placement(origins). I find myself constantly pulling a incorrect macros, or putting the right one in the wrong location, because all dimensions are typed in per profile. I will program a complete job, output to the USB and then upload the entire program into the control. This over writes any profile, support blocks, clamping positions, etc. So, each change to any individual profile made at the pc, means having to wipe all the setup I had done previously. And,of course any corrections or inputs I made at the control while running the job, never make it back to the original program in the pc. So, errors just persist. I know that there is a better way to operate. I know that I should be able to store an operation at the control, and reuse it, only adjusting the profile selection and dimensions. But I cannot find any reliable information on how to do it. The manual is garbage, and I can only find a dozen videos online, and 10 of them are in German. Can anyone please help me!? Any info, leads, or advice is welcome. Thanks All...


r/CNC • • 2d ago

SHOWCASE Double turret lathe for the apprentice shop

110 Upvotes

Double turret program was mostly just a test to see if the old machine still runs everything fine, Okuma LU-15M


r/CNC • • 2d ago

SALES How difficult is it for a garage shop to get customers?

0 Upvotes

Im In Central Texas. About a hour (traffic) from a major city. Say I decided to pop up a cnc shop in my garage. How hard would it be to get work?

Maybe like a Haas compact mill or a haas STY or DSY lathe. One or the other.


r/CNC • • 2d ago

HARDWARE Fowler calipers for general shop work, reliable enough?

2 Upvotes

I need another six inch digital caliper for a secondary workbench. It will be used for setup checks and rough in-process measurements, not final inspection on tight tolerances. Fowler is in my budget, but I have never owned one. How have they held up in normal shop use?


r/CNC • • 2d ago

OPERATION I´m surrounded by idiots

Post image
259 Upvotes

Production Manager: "The end mill cost 200€ it can do a second work piece."

The end mill:


r/CNC • • 2d ago

SHOWCASE I'm super proud of my billet 10/22 receivers!

Thumbnail
odysee.com
14 Upvotes

22lr is is low pressure cartridge but by no means was this a low pressure project. It may be my hardest undertaking yet. Not only did I have to do a ground-up redesign to make it approachable on my Tormach 770M and CNC in general (the originals are cast parts), but it has a ton of complex geometry inside that allows for the rest of the firearm to be fairly simple. Things like undercuts that have to match up from multiple operations, really tight and deep internal radii, and more. If you're curious about them, I don't focus a lot of the simple aspects of this build, the video mostly goes over the CAM and milling of that complex stuff.


r/CNC • • 2d ago

HARDWARE SUPPORT Flood coolant is killing the X limit switch on my Tormach 440. Anyone running an IP67 replacement?

1 Upvotes

Added the flood coolant kit to my 440 this summer, running a semi-synthetic at around 6 percent and cutting mostly aluminum. Big improvement for clearing chips out of pockets, but the X limit switch doesn't like it.

It's dropped the machine into reset twice in the last three weeks, both times mid cut after the flood had been on for a while. That switch sits right under the front of the table where the coolant runs off, so it takes most of it. Went through Tormach's limit switch troubleshooting steps and put a meter across NC and common, and the reading jumps around when i work the switch. Y and Z read clean. There's coolant residue all over the body, so my guess is it's getting past the seal and the contacts are going intermittent.

Tormach's replacement is $65 and it's the same dust sealed part, so i'd probably be back here in a few months.

Started looking at sealed ones instead. The ZING EAR G3s i ordered are IP67 and only a few bucks each, so for less than one Tormach switch i'll have spares on the shelf. Went with the pre-wired lead version so i can splice into the existing harness instead of fighting the terminals under the table. The DC rating is on the low side, but that's all a limit input needs anyway. No real world coolant life to report yet.

Still not sold that sealing the switch is the real fix. Tormach moved the MX machines to prox sensors on X and Y, but on a mill cutting aluminum all day i'd half expect chips packing onto an inductive face to give me the same false trips.


r/CNC • • 2d ago

ADVICE Broken bolt extractor advice for a bolt snapped below the surface?

3 Upvotes

A 5/16 bolt snapped about two threads below the face of an aluminum part. I can put it on the mill, but there is no room for welding a nut. I have not started drilling because I only get one clean attempt at this. What is the sensible order of operations?