Hey Bolt community! I thought I'd share my experience replacing the steering rack and pinion assembly on my 2017 Bolt. It's commonly repeated that this is not a DIY-friendly job, and I found that not to be the case.
As I understand, the steering rack is a common point of failure on 2017-2021 Bolts. Over time, lubrication is lost inside the rack and pinion assembly, leading to steering feeling more difficult and the wheels not returning to center after a turn. Left unfixed, this could eventually cause your steering to seize while you're driving. Unfortunately, it's not possible to effectively add grease where it needs to go while the assembly is installed, and by the time you've done all the work to get it out, it's easier to just replace it entirely.
The common advice I saw was that replacing the steering rack was not a job for your average DIYer, and that a lift was required. However, I found a video on YouTube of some guy doing the swap in his driveway, and I figured if he could do it, so could I. Rather than using a lift, he raises the front of the car and puts it on jack stands. Then, he creatively uses two floor jacks to lower the subframe and raise the motor slightly, creating just enough room to slide the steering rack out.
I mostly followed his narrated process, and I was able to complete the replacement by myself in 6 hours. I'm not a mechanic, but I'm an engineer that doesn't like hiring people to fix things. The new steering rack is the only part required (part number 42353783), and I bought one on eBay for $292 total. I'm very happy to have traded my Saturday for thousands of dollars in labor costs saved.
After completing the job, my assessment is that if you can change brake pads, you can do this too. It requires some mechanical know-how, but if you've worked on cars before you will be able to do this yourself. I do have a number of tips in addition to what's shown in the video:
Before you start, watch the video and note the tools required. At minimum, you will need two floor jacks (find a friend that has one or you may be able to borrow one from Autozone), a metric socket set up to 21mm (some of them deep), at least two feet of socket extensions you can stack, a breaker bar (or my preferred alternative, a big socket on an extension placed over a ratchet handle), a hammer, and a couple of metric crescent wrenches. An impact driver is helpful but not required. Even if you have to buy some of these, you'll still come out ahead.
He makes a few mistakes in the video: removing nuts that don't need to be removed on a mounting bracket, forgetting some 21mm subframe bolts near the wheel wells, and realizing pretty late in the process that he needs to lift the motor with a second jack. Take note of these when you watch the video the first time so you don't have to repeat his mistakes.
He says a lot of things about maintaining alignment for the new rack. The only thing you need to worry about here is installing the rod ends at the same position on the new part. Just count the turns on the nut to the point it bottoms out, then position the nut on the new rack at the same depth while you attach each rod end. Just before you make the final connection at the universal joint inside the car, make sure your wheels look straight and your steering wheel looks straight. You don't need to bother with the Sharpie marks he recommends. It's still a good idea to get an alignment afterward to make sure.
When you loosen the front of the subframe, back the bolts out by 5 turns instead of the 3 he recommends. There are a ton of threads still engaged and this gives you some extra room to tilt the subframe down that you'll need later on.
He recommends backing out the rear subframe bolts most of the way and then leaving them engaged by three turns (once you have the jack supporting the subframe). Just take them out entirely. Leaving them engaged does not give you enough room, and I think he realizes this himself and removes them later on.
You do not need to disconnect the sway bar. He recommended doing this because it seems like it's in the way when you initially try to pull out the steering rack, but his real problem was the motor mount. I didn't touch the sway bar, and I was able to remove the steering rack just fine.
You do need the second jack to raise the motor up to create enough space to remove the steering rack. I don't think there is a way around this. There's just not enough space with the motor mount connected to the subframe.
You can safely lower the subframe a LOT. Just go slow with the jack and listen carefully for anything getting caught. You'll need to lower it quite a bit for the steering shaft to clear the floor of the car. I found that once the motor was disconnected from the subframe and supported by the second jack, I could actually lower the subframe to the point that the car was fully supporting it—the subframe itself is not that heavy. If you're having trouble getting the steering rack out, you haven't lowered the subframe enough or you haven't raised the motor enough relative to the subframe. Just keep lowering.
I hope people find this helpful! Let me know if the process is unclear and I can try to give you some more tips.