I'm at my wit's end with my Analogue 3D, and after months of troubleshooting, I'm starting to think this may be an issue specific to my console rather than a widespread firmware bug or television compatibility problem.
Every firmware update after 1.5.0 results in a completely black screen. This started with 1.5.1 and has continued through 1.6.0 and 1.6.1. The only solution I've found is downgrading to 1.5.0, which restores normal functionality every single time.
What's Happening
The firmware installation itself completes normally, and I can see the update process on my television. However, once the console boots into the newer firmware, the screen goes completely black.
Interestingly, my Samsung S90C still detects an HDMI connection at 1080p/60Hz, but there is absolutely no picture.
When I downgrade to firmware 1.5.0, everything immediately works again, with both the Analogue 3D and Samsung S90C confirming proper 4K output.
Hardware Tested
Samsung S90C OLED — Firmware 2220
TCL 55R617 — Same black screen on firmware 1.6.1
Original Analogue 3D power adapter and USB-C cable
Original Analogue HDMI cable, along with multiple alternative HDMI cables
Complete Troubleshooting List
I've tried quite a bit at this point, including several suggestions from the community:
Firmware and System:
Installed firmware 1.5.1, 1.6.0, and 1.6.1. All produce the same black screen.
Downgraded to firmware 1.5.0 repeatedly. Works perfectly every time.
Performed a complete factory reset while running 1.5.0 before upgrading to 1.6.1. No improvement.
Repeated the firmware installation process multiple times.
Confirmed that the firmware installation is not being interrupted. I've sometimes left the console alone for 30 minutes just to be absolutely certain the update has completed.
SD Card:
Reformatted the SD card.
Tested a different SD card.
Installed newer firmware, removed the SD card entirely, and attempted to boot without it.
Confirmed the same black screen when booting without the SD card on both 1.6.0 and 1.6.1.
HDMI and Display:
Connected the Analogue 3D directly to the Samsung S90C, bypassing my HDMI hub.
Tested multiple HDMI cables, including the original cable supplied by Analogue.
Changed the Samsung HDMI input identification between PC and Game Console.
Enabled and disabled Game Mode.
Investigated Input Signal Plus. The problem existed even when this setting was disabled.
Disabled HDMI-CEC. My soundbar confirmed the setting was taking effect, but the Analogue 3D continued displaying a black screen.
Tested firmware 1.6.1 on a completely different television, a TCL 55R617, with the exact same result.
Power:
Result: Absolutely nothing has made any difference except downgrading to firmware 1.5.0.
Where I'm At Now
After testing two completely different televisions, multiple HDMI cables, different SD cards, factory resets, and numerous firmware installations, I'm increasingly convinced that something may be wrong with my particular Analogue 3D.
I initially assumed this was a firmware bug or some bizarre compatibility issue with my Samsung S90C. That's why I've spent months waiting for new firmware releases, hoping the next update would finally resolve the problem.
What frustrates me most is that 1.5.0 works perfectly. The console doesn't appear to be broken when running that version, which naturally led me to believe this was something Analogue would eventually correct through a firmware update.
Now I'm wondering whether I've spent all this time waiting for a fix to something that was actually specific to my unit and could potentially have been addressed through a repair or replacement months ago.
I wish I had recognized that possibility earlier, because I could have contacted Analogue about an RMA rather than repeatedly going through the same frustrating update and downgrade process.
Of course, I can't say with certainty that the hardware is defective. It could still be a firmware issue that only affects certain consoles. But after everything I've tested, I don't see much left that I can reasonably troubleshoot myself.
Thank You, Everyone
I genuinely want to thank everyone who has taken the time to read this post, offer suggestions, and help me troubleshoot. I really appreciate the community coming together to help me narrow this down.
Even though we haven't found a solution, the suggestions have helped eliminate several possibilities, particularly testing another television and performing a complete factory reset before upgrading.
I've already submitted a support ticket to Analogue, and at this point, it sounds like pursuing an RMA or replacement may be my next step.
I'm disappointed that it's come to this, especially after spending months hoping each new firmware would finally resolve the issue. I really do love what this console offers, and I just want to be able to enjoy it without being permanently stuck on an older firmware version.
If anyone happens to have a final suggestion or has experienced something similar that ultimately required a replacement, I'd still be interested in hearing about it.
Otherwise, thank you all again for your help. I'll update this post when I hear back from Analogue or have some resolution to share.