r/944 • • 5h ago

Question hatch shocks with ground that don’t separate glass?

1 Upvotes

hey all!

my glass is starting to separate on my 944 and with it getting cold, the frost and fog in the windows are going to start to get real annoying, and the gap in the glass isn’t helping.

does anyone know where to buy the “correct” hatch shocks for the 944 that doesn’t separate the glass? i’m about to put some silicone down on the glass to seal it up then hopefully find some better shocks to replace the incredibly strong ones right now.

let me know! :)


r/944 • • 20h ago

Headlight Upgrade

Thumbnail
gallery
105 Upvotes

Hello everyone,

Installed these United Pacific 7inch Headlights on my 944 and I think they look sweet! The provided halogen lights provide a good brightness upgrade to the stock lights while allowing you to run a brighter H4 bulb if you want. They have a clean daytime running light ring while also not looking super modern or tacky. The assembly is made of solid metal and lens is glass too so it will not yellow. Would definitely recommend!

Here’s is the link: https://link.amazon/B00qJWmjH


r/944 • • 23h ago

Question Hight torque starter alternatives in europe? SSP?

3 Upvotes

Hi,

Working on my GFs 944 (1982 2.5L early type) again. Now that it's getting cold the starter starts acting up. We managed to start the car with a couple love taps with a hammer on the starter housing while turning the key tho.

I want to look into upgrading the starter to a high torque one as mentioned in the nc944er YouTube video. https://youtu.be/qJvhgqFO3gM

As I am based in Germany, I would like to avoid shipping one from the US, like the IMI Performance starter. Currently looking at this one: https://www.heritagepartscentre.com/eu/95160410100hd-ssp-high-torque-starter-motor.html

Does anyone have recommendations or experience with the SSP starter?


r/944 • • 1d ago

Question Bore score

Thumbnail
gallery
7 Upvotes

Ive got a spare motor I’m “rebuilding” just looking to clean it up and reseal the whole thing to have a good condition motor on hand and I noticed that one of the cylinders has a inch long scratch that faintly catches my nail. The motor ran good in the car it was in 2 years ago but I want some second opinions before I go through with putting it back together. It’s just an NA so it’s not pushing boost or anything. If it’s at worst a little lower compression and some burned oil I’m good, but if it’ll be bad then I’d probably search for a different block. Thank you!


r/944 • • 1d ago

Santa’s 944 sleigh🎅

Thumbnail
gallery
60 Upvotes

Packed up the 944 sleigh today for some pre-holiday merch shipments. It’s the perfect delivery vehicle & staging area. 📸 https://www.instagram.com/midas.944


r/944 • • 2d ago

My 1990 Porsche 944 has had inner steering arm wear as an advisory for the last two years. The MOT is up so while I was ordering some bits I thought I'd change the arms. After cutting the outer nut off because I'm lazy, I could not feel any lateral play whatsoever. Does this mean the advisory was mi

Post image
3 Upvotes

r/944 • • 2d ago

Question Why have my front discs worn so badly?

Thumbnail
gallery
6 Upvotes

The inners are not even wearing evenly across the face. These are the front discs. Shot of the pads that are also wearing unevenly. Outsides don't have much wear. Rest of the discs look like they have been out to sea. They're 10 years old approx.


r/944 • • 2d ago

Question Is it possible for hubs to have too much surface corrosion? The edge of mine are looking a bit nasty. This is after cleaning them up with a flappy wheel. There's not a great deal of meat around the bolts anyway..

Post image
5 Upvotes

r/944 • • 2d ago

Resolved Q I come seeking knowledge

Post image
7 Upvotes

What is this piece I have circled? It’s under the intake manifold, close-ish to my firewall.


r/944 • • 3d ago

Door handle linkage update

Thumbnail
gallery
27 Upvotes

Posted here a while back asking about where to find a new door handle linkage for my 1983 944. Figured I'd give you an update. Ended up drawing the snapped linkage in onshape and 3d printing it in cf-nylon. Works great so far, and honestly probably as strong as the stock cast aluminium, if not stronger.


r/944 • • 3d ago

Question Shifter slip

10 Upvotes

Shifter all of the sudden got sloppy. I happen to have the only944 short shifter and linkage kit laying around. Will that fix this issue?


r/944 • • 3d ago

Resolved Q Guards Red repaint. Next up: reassembly.

Thumbnail
gallery
304 Upvotes

r/944 • • 4d ago

Here's my 944 in Forza Horizon 6.

Post image
76 Upvotes

It's based on my IRL 944... Minus the *minor* modifications... Of the mid mounted LS4. Also, I haven't posted in a while and wanted to stay active a bit.

Enjoy!


r/944 • • 4d ago

9 Porsche 944 Quirks in 44 Seconds

Thumbnail
youtube.com
9 Upvotes

Had some fun making this one. I was thinking about doing a similar format for the maintenance oddities with the 944 next. Things like timing belt change frequency, oil filter milk shake, heater getting stuck on, etc, lmk what you think!


r/944 • • 4d ago

944-Cayenne and 944-996 brake adapter kits — PRICE INCREASE EFFECTIVE JANUARY 1, 2027

Thumbnail
gallery
28 Upvotes

Hi, as with everything else it has become more expensive to produce these kits over the last year and a half. Hopefully the next 7 weeks or so is enough time for anyone on the fence to decide and save some $!

I have sold and shipped off over 70 of the Cayenne front adapter kits around the world. There are 15 Cayenne rear caliper adapter kits out there and several 944-996/986 front kits too.

944-Cayenne FRONT brake kits prices effective 1/1/27, includes US shipping:

1982-1986 NA, 17Z brackets only $275
— add $400 for 330x28mm modified rotors
—— add $75 for drilled/slotted rotors
— a 330x32mm 2-piece rotor option exists, PM for details

1987-1989 NA, 17Z/18Z adapter Kit $335
— uses 996T/997T/Panamera discs on your 87+ 944

1986 turbo, 17Z brackets only $375
— add $400 for 330x32 modified rotors
—— add $75 for drilled/slotted rotors

1987-1995 turbo/S2/968 (non-M030), 17Z/18Z adapter kit $425
— uses 996T/997T/Panamera discs on your 87+ 944

REAR CAYENNE KITS:
1982-1985 (steel trailing arm cars) $445
1985.5-1986 (aluminum trailing arms, early offset) $445
1987-1995: I do not have a late offset specific kit. My recommendation is to backdate your rear hubs to early offset, use my 85-86 kit, and add a factory early 944 21mm spacer and longer studs. I can help procure those parts if needed.

————————-

944-996/986 front caliper adapter kits pricing effective 1/1/27:

1982-1986 NA, 996/986 brackets only $375
— add $400 for 330x28mm modified rotors (for 17” wheels and 996 calipers)

—— add $75 for drilled/slotted rotors

— add $600 for 298x24mm custom rotors (for 16” wheels and 986 calipers)

1987-1989 NA, 996/986 adapter Kit $425
— allows the use of factory 986/996/981 298/318/330mm discs on your 87-89 944

996 REAR kits still in development but coming soon.


r/944 • • 4d ago

Carpokes.com

17 Upvotes

If you own a Porsche 944 and haven’t checked out carpokes.com, you’re missing out.
I’ve been on pretty much all the Porsche forums over the years, and I can honestly say that carpokes.com⁠ is by far one of the best resources I’ve come across.
The forum is for all Porsches, but it has a particularly large and active 944 community.
What makes it different is the level of technical knowledge and the work people are putting into understanding these cars. Tom, the person who created the forum, along with several other extremely knowledgeable members, is actually digging deep into the DME code to figure out exactly what controls what. They’re working to understand how the factory engine management system operates at a much deeper level. That kind of information could be incredibly valuable for all of us trying to keep these cars running, troubleshoot problems, and improve them.
One example is that Tom actually designed and built a control box specifically to test and understand how the Idle Control Valve (ICV) works. And rather than just keeping that knowledge to himself, he posted detailed instructions so anyone interested can build one of their own.
There are also some excellent tutorials on the forum covering how to test various components and systems on these cars. It’s the kind of practical information that can save you hours of troubleshooting and a lot of unnecessary parts swapping.
Another really cool section is dedicated to 3D-printed parts. Members are designing and sharing printable files for all kinds of 944 components, including parts that can be difficult to find or are no longer available.
I don’t have any affiliation with the forum. I’m just genuinely impressed with what Tom and the other members are doing. It’s great to see people going beyond simply discussing problems and actually developing tools, sharing technical knowledge, and figuring out how these cars work at a deeper level.
If you’re into Porsches, especially the 944, do yourself a favor and check it out:
https://carpokes.com
The more people who contribute, the better this resource will become for the entire Porsche community.


r/944 • • 4d ago

Question need advice on pistons and machining

3 Upvotes

So i have pulled my 8v NA 2.5 engine because the alusil bores are toast. I've found a local machinist that can put in dry sleeves and now I have 3 options.

Since the factory pistons are in OK shape except the piston rings being able to move up and down, they can widen the canals where the rings sit and just put in thicker steel rings which i've already found and am able to source.

I am questioning this option because i am not sure if factory cast aluminium pistons can even run in steel dry sleeves. I've also heard mention of some ferrous coating on them that might cause problems.

Option 2 buying forged NA pistons.

Option 3 buying forged turbo pistons.

How big of a difference does it make to run turbo pistons with lower compression ratio without any boost? Because they cost pretty much the same and it would be nice to have the option to turbo it without needing new pistons in a couple years.

How realistic is it to turbo an NA with just forged pistons?

Which piston manufacturer should i go with? (prefferably available in EU)

Is dry sleeving this block known as a reliable procedure?

Since im already machining everything, are there any known easy ways to make more powa safely?

I will appreciate any useful advice i should be aware of before proceeding with this build, and also does a list of needed parts for a complete engine rehaul exist?


r/944 • • 4d ago

Question Lame or Classic? 🤔 Phone Dials are growing on me

Post image
191 Upvotes

When we first got our 944 I was sure we would quickly upgrade the rims. But as time keeps passing I find myself really loving the phone dials. I seem to have a love hate relationship with them. On one hand I want a more sporty look and thinner tire. On the other hand I don’t want our 944 to look like it has unnaturally “modern wheels” on a beautifully nostalgic car. What’s your take, seems like the community falls into a similar camp?


r/944 • • 4d ago

Question Cooling system questions

2 Upvotes

My 944 used to run right in the middle on the temperature gauge. Just recently, I have replaced the water pump and thermostat. My old thermostat was 176 degrees... the new one is 181. Now my car runs at the 3/4 mark on the temp gauge (technically okay?) but I am wondering why it is hotter now. After driving... the upper radiator hose reads 180 degrees... lower hose 140 degrees. Any guesses? Could the new thermostat just open later? The needle stays here consistently no fluttering.


r/944 • • 4d ago

Repairs Engine Sounds

11 Upvotes

Howdy folks

Finally getting to run my 951, but it's making some potentially awful sounds.

  1. A VERY high pitched whine, almost sounds like bird.

  2. A somewhat low, quietish tumbling sound, kinda sounds like gravel in a paint can.

Couple of notes for the video. Had the head refreshed with newly cut seats, and there's only the coolant that was in the block. Additionally, it's on jackstands. Running VR1 20w-50. New turbo K27/6 and it hasn't been tuned for it yet. I'd like to run it more to try to pinpoint where the sounds are coming from but I fear for the health of the engine if there's something wrong with it.

Hopefully one of you kind folks will have some wise words.


r/944 • • 4d ago

Question Anybody know what this part is called?

Thumbnail
gallery
5 Upvotes

Hey guys, first Time posting here. I’ve be rebuilding my 1984 944 N/A and there is this one piece i just can’t find online. If anyone knows the name of it or where to by it that would be super great thx!
I know it’s for the coolant system and it’s placed in the rear of the motoer but that’s about it.


r/944 • • 5d ago

Question How to get stuck slave cylinder bolt off

Post image
5 Upvotes

Doing my slave cylinder on my 85.1 944 and I tried to undo this bolt and it’s completely seized on there, wondering if any of yall know how to get it unscrewed, thank you!!!


r/944 • • 5d ago

Turbo Tuesday 💨

Post image
268 Upvotes

Let’s see those 951s!


r/944 • • 6d ago

Resolved Q Rear speaker

Post image
13 Upvotes

Hello Does anyone know if these speakers will fit in the rear of a Porsche 944?