r/4Runner_1stGen • u/toylizard • 22h ago
85 4Runner
4XNation
r/4Runner_1stGen • u/Kentness1 • 1d ago
I can’t believe that after over two years I have this thing back running! It’s not perfect yet by any means, but I’m very proud of having gotten it done holding very little actual knowledge of how to do it.
r/4Runner_1stGen • u/Sea-Standard8981 • 4d ago
Hey all!
So question for everyone.. when i bought my 89' the previous owner included a 2inch lift kit, and bumper. I'm realizing that I am wanting a 3inch.. and a different bumper.
Would I be able to sell both on like FB market place? What would a fair price be? Below is what he included. Do all of these only work with a 2inch lift? Or can i use some of these with a 3inch?
2” Dobinson lift kit
Front and rear shocks
Torsion bars
Replacement leaf springs
Steel bumper from hammer head outfitting
r/4Runner_1stGen • u/VeterinarianNo3177 • 4d ago
Finishing up the sound dampening in the back…cleaning up the seats now to reinstall… and it’s got me thinking…
Can you guys show me some rear seat delete set up??
How do you like them??
r/4Runner_1stGen • u/Unabletosurf • 5d ago
Hey all, I’m looking at getting a new radio for my 89 4 runner and wondering which wiring harness would fit for this part number radio: 86120-32130
I bought the Metra** **71-1761 reverse harness.
This will fit right??
r/4Runner_1stGen • u/Commercial_Goose8985 • 7d ago
Swapping to 30 spline and 6 shooters on my first gen. First time opening the knuckles on this side of the truck anddddd….. look what I found a skeleton bearing. And to top it off there was not even a bearing on the bottom of the knuckle…… PSA do your services people.
r/4Runner_1stGen • u/RareDiscipline9 • 10d ago
Banger of a season. Six months until we do it all over again.
r/4Runner_1stGen • u/haloscrogings • 12d ago
That looks like an after market logo to me but am not sure. (1986)
r/4Runner_1stGen • u/cforman158 • 13d ago
Hello I’ve been following the tutorial with the jumper to set my distributor timing on 86 4Runner turbo with ct26 but every time I set it between 5 and 8 degree the car just stalls out a lot and runs bad. At 12 degree it runs good what could this be? Looking to get it running perfect here
New distributor, timing chain (been checked twice), plugs, wires, o2 sensor
r/4Runner_1stGen • u/Sea-Standard8981 • 19d ago
Finaly got my 89 4runner! She needs some work but im loving her!
Question for yall.. i was working on changing fluids and the previous owner put the oil drain plug on there tight, when i was trying to get it off i was starting to stip the bolt. Due to the location of the plug its a challenge to get to.. any advice?
r/4Runner_1stGen • u/PeacefulPirana • 21d ago
Hey guys, looking for a mostly stock 1st gen in good shape, that drives so I can use on weekend and my son and I can fix minor things and give to him when he’s older (he’s 8). Not museum quality and some honest wear is fine but not beat up / rusted out. Around 10-14k budget. Let me know. I’m in the Atlanta area.
r/4Runner_1stGen • u/Unabletosurf • 24d ago
This little truck is starting to remind me more and more of a politically divided thanksgiving dinner. The more I stay at the dinner table or dig into this thing, the more problems start to show up.
Thanks to all who commented on my last post trying to help with the back window. Taking-some peoples advice, I checked both fuse boxes and found that the some of the fuses under the hood look very corroded, while under the drivers side box had a mess of wires that seem to have some connections disconnected and other new ones punched into existing fuses. My truck has quite a few amps and subs and whatnot.
I’m wondering what my course of action is here. Do I try and “un-fuck” this myself? I’m afraid my frustrations might lead me to get to the point of an early burnout.
Another option I’ve been thinking about is to spend the 250-300$ on a used oem radio setup and 4in oem speaker set, take the truck to an electrical/sound guy, and pay them to take out the old components and install the new components. Perhaps fixing the root of my wiring issues would ease my back window problems at the same time.
My issue is I don’t have the most amount of money for something like this, if it were to be very costly. But then again, she is too pretty not to fix.
Either way, I’m assuming something wrong with the wiring is sucking the life out of my newborn 3 year old battery, and I can’t even drive her to the beach if I don’t figure something out soon.
r/4Runner_1stGen • u/Unabletosurf • 25d ago
Just bought this beaut but the previous owner messed with the sound system and all of its wiring. My back window won’t power down and my 3 year old battery is draining. Anybody have any suggestions where to start? I’ve never done any wiring, tried to take out the motor in the back but stripped one of the 3 screws holding it on and can’t get it out. Popped the top for the little window motor and all the teeth seem fine, so I’m thinking it has something to do with the electrical.
Also, anyone selling interior pieces? The P/o also rhino lined the thing lol.
r/4Runner_1stGen • u/Dapper-Stress9760 • 25d ago
Been doing a partial front end rebuild. My wife was wondering why I painted something no one will see..I’ll post it here so a few people can see it
UCA/LCA rebuild, energy suspension bushings
OEM upper and lower ball joints
Bilstein 4600 shocks
New disc brakes front and rear
New bearings
Trakmotiv HD CV axle
Mots of money and time, one step close to completion..
r/4Runner_1stGen • u/Last_Entertainment86 • 28d ago
Mines is the single wire and it broke off the back of the transfer switch.
I found one from a buyer who claimed it came from a 1986, but it didn't have the same connector. My 4runner is a July production date.
I'm seeing Land Cruisers that are similar and these two wires which are similar.
Can anyone help me if they sourced an alternative switch and it worked fine on their 1st gen?
Also, the wire harness coming from the passenger side engine bay to where the starter is located, isn't that wire green?
Any help would be greatly appreciated.
r/4Runner_1stGen • u/nuttisel • 28d ago
r/4Runner_1stGen • u/Dapper-Stress9760 • Oct 21 '26
I’m trying to find the proper seal for the engine side of the spindle. The Toyota part 90613-60004 does not fit in the rear.
Attached is the old seal, new seal, and the spindle (off an 88 4Runner.
Anyone do this rebuild and run into this issue?
r/4Runner_1stGen • u/allinthgldnafternoon • Oct 20 '26
(Cross posting from the general r/4runner)
Have an opportunity to buy a 1987 4runner turbo in good condition (little rust, well-maintained engine, 206k miles) for $17k. I currently need to drive about 80 miles a day for work, but that number will hopefully drop in a year or two. Other than that, just need it for getting around town, occasional trips out of the city. Could a 1987 turbo do it, or am I going to spend a ton of time working on the car? My spouse is an aviation mechanic, so we can probably do a lot of work ourselves, but I need it to be pretty reliable and I'm concerned about parts availability.
ETA: Thank you all for your help on this! I need to turn off post notifications so that I can have my inbox back again, but this has been really helpful!