** /r/tDCS DIY Howto.**
Here you can see my setup and the schematics
This is a DIY tDCS device running on a single 9V battery, with an on/off switch and current regulated between 0.3mA and 4.5mA, which is selected with a large knob. The connectors and wires are color coded to prevent accidentally reversing the polarity. The device has a Led to show that it is on and a Ammeter to show the current that is flowing through the electrodes. I expect battery life to be in excess of 50 hours.
Why you should use this design:
It is reasonably save. The LM334 limits the current in this setup to 4.5mA max, in the case you seriously screw up, there is a fuse that will blow.
This design is simple and has been tested. This setup performs as well as a professional tDCS device. Both the electrodes and the device use banana jacks, making it very easy to switch either electrodes or electrode wires (some research has been done with larger electrodes than I suggest in the parts list, which can also be bought on the same sites listed below).
Skills Needed:
Basic Soldering, If you've never done it before, ask a friend to do this for you.
Not much Electrical Engineering is needed, just some basic understanding of how a multi meter works and the ability to put the parts in the right order.
Basic sewing. This was hard for me.
Advanced use of search engines and a strong analytical mind to interpret research papers. It is quite hard to understand what researchers actually have been testing and how succesful they were. Don't think you can wing this part, since you might end up putting the electrodes on the wrong spot. Since it is nearly impossible to determine if your brain manipulation program works, due to placebo and lack of double blind experiments, you will have to rely heavily on the research papers.
Tools Needed:
Soldering Station
Hot Glue Gun
Screw driver
Bread Board
Multi meter
Dremel with various cutting tools
Sewing kit
Parts Needed:
Shipping costs are not included in the prices.
Jameco:
IC,NSC,LM334Z, TO-92, Price: $0.79 Part #: 23739
SWITCH,ROCKER,R13-66A-B-02 Price: $0.99 Part #: 31601
POT,53C3250,RV4NAYSD251A Price: $9.95 Part #:241584
KNOB,1/4"SHAFT,29MM,RN-113A Price: $0.95 Part #:264892
Ebay:
9V battery holder Price: $1.50
Littelfuse 3AG 10mA 312 Fast Blow Fuse Price: $1.45
Steren Banana Jacks (red) 10x Price: $3.44
Steren Banana Jacks (black) 10x Price: $3.44
Panel mount 3AG fuseholder Price: $3.50
Neosport Sport 2.5mm Neoprene Cap Wetsuit Hood Price: $23.05
5mA DC AMP Analog Current Panel Meter Ammeter Price: $5:45
Shoe Goo Price: $3.74
Project Box (watertight) Price: ~ $5
Banana Plugs, black 1x Price: ~$1
Banana Plugs, red 2x Price: ~$2
Jo-Ann Fabric:
Velcro Type 90029 black Price: 3.99
Amazon:
2" x 2" Sponge Electrodes Price: $48.59
The amazon order took very long to ship, I ordered here:
http://www.4mdmedical.com/
These are expensive electrodes, but are the best I could find. They have rubber backing and sides, which limits the leaking of saline.
Other Parts Needed:
15 Ohm Resistor
4k Ohm Resistor
16 awg stranded Wire (speaker wire)
9V Battery
Led
Textile Paint
Thread (Black)
Hot Glue
22 awg solid core Bread Board wire
Solder
Things to keep in mind:
Get a watertight project box. This is a messy adventure. Insulate. I did this with hot glue, using shrink tube would probably be better. I liked hot glue, since it prevents parts from touching each other if I would accidentally drop the box (this isn't visible in the open box picture since this was made just before I filled up most of the box with hot glue). If you make holes, for buttons and the like, make sure you seal wherever possible to prevent water from entering your tDCS device.
If you want to test the resistance of your skin while breadboarding, use both electrodes on one arm, don't use your head, your arm is good enough to tell if it works or not, and the risk of accidents is significantly lower that way. I even avoided this and used a 4.6k Ohm resistor for all my testing.
I used 10mA Fast Blow fuses, 5mA would be better, but this was the most cost effective way of doing this. Make sure you get Fast Blow.
Don't leave out any parts that are there as a safety measure, don't try to substitute with cheaper or more readily available parts (unless you are really sure you know what you are doing). The device itself is already very cheap, there is no point in trying to save a few bucks by leaving out the fuse or LM334, while increasing your health risk.
There is no additional resistor between the battery and anodes as is sometimes suggested, because in my experience this drops the overall voltage too much, resulting in too low current at the electrodes. I think the LM334 and Fuse are adequate safety measures as is.
Once you start using the device, don't ramp up the current right away, this will not only create some discomfort, but will also cause irritated skin, ending with lesions after frequent usage. Ramp up slowly over the course of 1 to 2 minutes, to a maximum of about 2mA with 1 anode or 4mA with 2 anodes. If you think that more current is better, read more research papers. The 4mA max is meant to be used with either large electrode pads or multiple anodes.
Don't use the electrode on the same spot for two weeks in a row using 2mA, this causes brown crusty lesions on your skull (which probably go away after a while). If you really insist on using it daily on the same spots, you could try to do so at 1mA instead, but this is not guaranteed to prevent lesions.
How to make the device:
This is pretty straight forward and takes relatively little time.
Use these schematics. R means resistor, the little triangle is an LED. The longer lead on the LED is the positive one. The Pot has three leads, use the multi meter to figure out how to wire it. Make sure you use the LM334 DataSheet to determine which wire goes where. First build the circuit on the breadboard, then solder the parts together and mount them in the project box. Close up the project box before you attempt to use the device for the first time. Connect the banana plugs to the 16 awg wire, these are your electrode wires.
You can cut the rear of the ammeter to make it shorter and solder directly onto the leads.
Howto make the cap:
Making the cap took the most time out of the whole process for me.
Measure Nasion and Inion, Use this page to design your Electrode Cap
The center between the two earlobes and the nasion and inion is where cz is located.
Nasion is between your eyes, Inion is a ridge (about 10cm wide) at the base of your skull. To find inion, take middle finger and index finger of both hands and slowly roll over the bottom of your skull, you'll find the ridge
Then use the fabric paint to draw the electrode grid on the inside of the cap. This will aid you in placing the electrodes on the right location. If possible write the names of the electrode positions next to the grid points.
Sew strips of Velcro into the cap at locations you are interested in testing.
Glue the other side of the Velcro onto the electrodes, using the Shoe Goo. The back of the electrodes are made of natural rubber, many regular glues will not work, make sure you have something that specifically glues onto natural rubber.
If you get the cap I suggested, use it backwards, that way you can mount electrodes on your forehead.
Howto make normal saline:
Take a bit of hot water (doesnt have to be boiling), now add salt and stir. Keep adding salt, until the salt no longer dissolves in the water. Then pour the water in different large container, while keeping the salt crystals in the original cup.
Now you have a maximum strength saline solution of 6M NaCl. This should be diluted by adding about 40x the same amount of water that you had in your original container, to reach a dilution of between 0.07-0.15M NaCl. As you add water, the resistance goes up and you should experiment to figure out which ratio works best for your purposes.
Note: If you have a scale that measures grams, you can also take 9 grams of salt and add it to a liter of water, that will give you a dilution of approximately 0.15M.
What is lacking in this setup:
Ideally, it should have components (like an LED bar) that allow you to test the resistance before you turn the current on, that way you would know if the resistance is too high due to incorrectly placed electrodes.
The current scales logarithmically, I think this is a feature of the LM334.
I used Eagle to design the schematics, this program is free for personal use. Here is the project file.
I've hit the max article length so check the comments for more info.
Disclaimer: I'm not an expert and don't know what I'm doing.