r/hackrf • u/frankentriple • Aug 09 '26
I hired a radioman to run my hackRF for me. I gave it to an AI. He's way better than I ever was or could be.
This may be a little too far down the AI rabbit hole for a few of you, but I'd like to report my results from just a few days of work.
It started with Hermes Agent. No this is not an ad for them, not affiliated in any way. I jsut use it as a harness because it suits my needs, you may want to use openwebui or openclaw or any of the harnesses out there, that's not what important.
I gave it the root password to my debian vm and proxmox host, and the AI SSH'd in and first setup an API key for hygiene purposes then used it to create an ssh key on the debian box (again, for hygiene) and setup usb passthrough on proxmox so the lxc could talk to the hardware, then installed gnu radio tools on the debian host, establilshed communcations with the hackrf porta pack, correctly determined what it was, and updated the firmware to the latest mayhem for me.
It then started scanning the band from bottom to top and built a db of local signals in the area to expect. Its scanning the entire available spectrum every 2 seconds and notifies me when it sees a new signal. It then switches to fine resolution and listens real hard at max sample res to get a good idea of exactly what it is, then reports the whole thing back to me.
i'm pretty blown away by all this. I expected some kind of result but wow.
edit: I had my guy write up a how-to if you want to do it yourself:
https://github.com/h00nigan/sparky-setup-guide/blob/master/Sparky-Setup-Guide.md
2nd edit: I'm thinking about giving him a yaggi on a servo he can control so I can get direction as well as range/signal strength.
3rd edit: We just chased a signal down to an undershielded crystal oscillator in the plc that controls my 3d filament dryer. Its SCREAMING in rf at 10mhz.
4
u/jrsphoto Aug 11 '26
this page is a perfect example of why a lot of people don't post things they do with LLM's/Agents. Because people come out of the the woodwork with "why are you using AI", "Just learn it", or any of a number of other phrases. I use them every day, and do some pretty cool shit that I would never in a 1000 years have been able to do like 3d volumetric rendering of my ADS-b antenna's receive performance (https://github.com/jrsphoto/ADSb-Vue). I know what I wanted, I know the terms, but not the math. Claude lets me! I have an idea, I go to claude, and we work it out. If it seems like it might work, we might try some code and see. To the OP, keep on keepn on.
1
u/frankentriple Aug 11 '26
I ain’t paying no attention to the haters. I did three years worth of work in three days now I’m on to the next one. I’m about to get a WHOLE lot more proficient with my flipper zero.
3
u/CriticalJuggernaut75 Aug 09 '26
Did the same thing. Then upgraded to 2 hackrf (one pro) both connected to an opera for multi antennas. Still working on getting all of the decoders I can and data enrichment via online sites. Been fun
1
u/frankentriple Aug 09 '26
Ah ok, you went the multi-antenna route with a electronically operated antenna switch? i am thinking about getting one of the log-periadic antennas on alie that will talk/listen 50mhz to 6ghz but they are hella directional. I'd have to rotate it or setup a grid of them. If I setup a couple of them though I could get some https://en.wikipedia.org/wiki/Passive_radar working, I think. I can definitely do the signal processing :)
2
u/CriticalJuggernaut75 Aug 10 '26
k, that's very cool and haven't heard of it before. My goal was to build a full spectrum analyzer to detect all signals and sources on those frequencies to a) determine what was out there for logging and analysis b) baseline frequent known assets to determine what was net new. (this wa helpful to answer the question "if someone broke into my house to rob me how would I identify them?". if they are carrying a phone, etc.
With that, it's just been very cool to track, log, and see all of the different types of assets out there. I live in SF so I see a ton of shipping containers, boats, planes, etc. Always building it up but the main thing now is getting decoders for unkown and weird signals.
Of course the Bluetooth, WiFi, zigbee, etc stuff is nice.
Not sure if anyone else is doing this but happy to share what my harness looks like (claude code) if you want.
3
u/frankentriple Aug 09 '26
The first real job I had him do was take three measuments of the entire rf band and swapped antennas after each three sweep run. We compared average signal quality noise floor and number of signals received and decided on a best all-rounder and when to switch to a different one. We also discovered my mag mount antenna needs a ground plane and can barely hear without one. Put it on a metal biscuit pan and its hearing much better now.
2
u/MinorLatency Aug 09 '26
I am looking for a signal, could this work as a sorta ‘shazam’ for sdr?
6
u/frankentriple Aug 09 '26
the report format:
Full-spectrum sweep complete, cap'n — 1 to 6000 MHz, 2400 rows, monitor paused and resumed (standing order intact). Here's my analysis, one sentence per signal: The strongest signals (whole spectrum):
876.4 MHz (−51.1 dBm) — A strong 800/900 MHz signal, likely a cellular uplink (Band 5/8) or a trunked radio system.
543.6 MHz (−51.1 dBm) — UHF TV band (channels 26–30) or a land-mobile repeater.
144.2 MHz (−51.9 dBm) — The 2-meter amateur radio band — a strong local ham repeater or simplex signal.
766.6 MHz (−52.0 dBm) — More 700 MHz cellular downlink energy.
743.0 MHz (−52.1 dBm) — Continuing the 700 MHz cellular/PSR cluster.
120.0 MHz (−52.4 dBm) — VHF airband — a strong local aviation/air-traffic signal (near the Katy flight path).
751.0 MHz (−52.7 dBm) — More 700 MHz cellular downlink (Band 13).
534.0 MHz (−53.0 dBm) — UHF TV band (channels 26–28) or a land-mobile repeater.
105.6 MHz (−53.1 dBm) — Another FM broadcast station (near 105.7).
89.2 MHz (−54.4 dBm) — FM broadcast (near 89.1, often a public/NPR station).
592.4 MHz (−54.5 dBm) — UHF TV band (channels 33–36) or a wireless mic/utility signal.
2511.6 MHz (−54.9 dBm) — S-band, likely a satellite downlink or a nearby radar/telemetry source.
870.6 MHz (−54.9 dBm) — 800/900 MHz cellular downlink (Band 5) or trunked radio.
192.4 MHz (−55.5 dBm) — VHF, likely a two-way/utility radio or a TV channel 7–13 remnant.
2448.8 MHz (−55.9 dBm) — 2.4 GHz WiFi — your own home network (channel 9-ish) is the strongest WiFi signal.
Bottom line: The RF environment is dominated by cellular (700 MHz cluster), FM broadcast, and VHF airband/2m — all consistent with a suburban location near cell towers, FM transmitters, and the local flight path. Your own 2.4/5.8 GHz WiFi is present but weaker than the broadcast/cellular signals. No unexpected or anomalous signals — it's a clean, normal residential RF picture.
1
u/frankentriple Aug 09 '26
Sparky, do a quick scan of the spectrum and find something interesting. Do a full recon of the signal and give me whatever information you can find and suggest ways to make the process faster smoother and better.
RF Recon Report — Windlewood Rig, 2026-08-09 *A demonstration sweep for the crew, run end-to-end on the big ears. Full methodology below.*The find: 144.289 MHz — a real 2m ham-band beacon carrier A genuinely interesting catch, because the coarse sweep nearly walked right past it. On the fast 1:6000 MHz survey, 2m looked quiet. It was only a full-resolution stare that revealed a strong carrier the wide sweep couldn't resolve. Frequency • Value: 144.289 MHz (2m Amateur band) Power • Value: −13.3 dBm (strong) Bandwidth (−20 dB) • Value: 0.24 kHz — nudely narrow (CW class) SNR • Value: 64 dB Modulation • Value: none — steady, unmodulated CW/beacon carrier Envelope • Value: steady (ratio ≈1.0, no dits/dahs in the 12 s window) Persistence • Value: confirmed across repeated stares + gain-scaling test Likely an idle 2m repeater or a CW beacon (common on 144.20–144.40 in Houston area). The demod audio is saved (
/tmp/beacon_144289.wav) — it's just a steady tone since the carrier is unkeyed; a longer stare would catch the beacon's ident.Methodology (how we got there)
Sweep — 2401-line wideband survey (1–6000 MHz, 200 kHz bins) to map the spectrum and rank the strongest bands globally.
Find — peak-ranked the survey; identified candidate bands. Then... (1/3)
Verification (so we don't chase ghosts) Equipment limitations that affected the outcome
Stare — re-scanned candidates at 20 kHz full resolution (vs 200 kHz coarse). This is the key step that surfaced 144.289 MHz at −13.3 dBm when the coarse sweep showed the band as "clean." Also reconfirmed 60.002 MHz at −4.6 dBm (the house ESP32 clock-radiation — 240 MHz÷4 signature, matches our documented case).
Recon — 6-second IQ capture at 2 MSPS, FFT power spectrum for carrier location/bandwidth, FM de-discrimination for modulation, and amplitude-envelope analysis for keying. Produced calibrated specs above.
Persistence: target stable across 3 repeated stares at the same non-boundary frequency.
Gain-scaling test: power tracked the antenna-path gain by ~47 dB (LNA40→0, VGA24→16: −12.8 → −60.4 dBm). Internal HackRF DC/LO artifacts do not scale with gain — so this is real on-air RF, not a spur.
Clipping check: an earlier capture was overloaded (I-channel saturating); re-captured at LNA8/VGA8 for a clean, unclipped measurement.
Coarse-vs-fine resolution gap — a one-shot 200 kHz sweep missed this signal entirely; only a 20 kHz stare found it. A full 1–6000 MHz stare at full resolution would take minutes, so we must budget where to look fine.
The mag-mount whip is electrically short on 2m — needs ~49 cm quarter-wave but is only ~25 cm, so it's inefficient down there. That we still pulled −13 dBm with an electrically-short antenna means the source is genuinely strong/close.
Single-center IQ capture — with the carrier landing centered in-band at high gain, I/Q imbalance and DC leakage risk confounded the first measurement; had to drop gain and re-capture.
No
hackrf_recon.pyon the box — I had to assemble the SDR analysis by hand (numpy FFT + FM discriminator) instead of a one-liner. Functionally complete, just slower and more error-prone. (2/3)How to do the job better --- Been a genuine pleasure, Cap'n — the crew got a real signal chased from sweep to ident, no theatrics. Want me to stare down 144.289 over a full minute to try and catch the beacon's call sign, or hand this off to Sparky for a cross-check? (3/3)
Monitor service auto-restart race — the wideband monitor seizes the radio seconds after stopping, so every capture had to be wrapped as a single atomic stop→run→restart command. (The
bigearswrapper handles this, but calling the raw tool doesn't.)
Two-pass sweep strategy as standard procedure: always pair a fast coarse survey with a targeted full-res stare on any band that looks interesting-but-quiet (2m especially). The stare is cheap (~5 s) and catches what the survey hides.
Drop
/usr/local/bin/hackrf_recon.pyonto the Proxmox box to restore one-shot full recon (mod/BW/power/audio in a single call) instead of hand-rolled analysis — faster and less bug-prone.Bundle a proper resonant 2m/70cm antenna for the demo kit. A cheap dual-band might add 10+ dB on 2m and turn "maybe a beacon" into a signal we can hear in the demod audio.
Keying-ident capture: for likely-CW beacons, capture 30–60 s so the beacon's Morse ident appears in the envelope (12 s often just catches an idle/keyed-down period).
-2
u/fistofreality Aug 09 '26
You need to write an application to see this? I would’ve just googled a band allocation table.
2
u/Laminarflows Aug 09 '26
Instead of a yagi and servo could you use three antennas and triangulate? Would that be cheaper to set up?
2
u/frankentriple Aug 09 '26
I dunno, I'm an IT nerd more than an RF nerd. I could cobble together an arduino/esp32 with a servo controller hat easier than I could come up with three directional antennas and a way to multiplex them.
1
2
u/Residentlord777 Aug 10 '26
Can the model be build to run aB Bladerf radio or a sdrplay rsp1a.
1
u/frankentriple Aug 10 '26
If it has an api or is controllable by command line from a computer the answer is a resounding yes. In this case both of these are controllable by gnu radio so he's already halfway there. He'll walk you through getting the hardware talking and then take it for a stretch and see what work and what don't. he keeps banging on it with slightly different syntax and remembers what works and writes it down as a stored procedure and then keeps on brute forcing the api. Dude is an animal, i'm telling you.
He went from "I see a device on the serial bus on our proxmox host, should I pass it through to our tools vm?" to "I have a 2 meter signal at -40dbm, no modulatio just pure carrier" in like 4 minutes. That included updating firmware in everything.
2
u/Weekend365 Aug 09 '26
Just saying
More than one way to do this.
Some are shorter and more direct.
2
u/frankentriple Aug 09 '26
Yeah, but its kinda part of the bigger picture I have going on right now trying to automate my house with AI. So far I'm up to 3 AI subagents running different aspects of my house, handing jobs back and forth and taking care of business. Keeping the neighborhood under complete RF surveillance was a tiny part of that infrastructure I'm setting up and I thought it was pretty neat and wanted to share.
And now I have a full-time radioman on the radio, running off a local model on my rtx4070, ready to answer any question and implement any plan at a moments notice. I talk to him on discord.
2
u/DaturaSpirit Aug 09 '26
Automating your house with AI? You have alot of faith in AI lol.
-2
u/frankentriple Aug 09 '26
One of my AI agents is Jarvis, my butler, who runs my HomeAssistant instance. He's going to be taking over my household finances soon too.
1
u/fafnir665 Aug 10 '26
I did similar, but gave it root on a raspberry pi connected to my hackrf and operacake. I printed some helical antennas that attach to a dome to evenly space them out, so it switches between common band’s optimized antennas via the opera cake
1
u/frankentriple Aug 10 '26
Ok, I want to know about this "printing antennas" thing. Expound, please?
3
1
u/Chance_Ad5583 Aug 09 '26
I’ve been running Hermes agent at home for couple months now that’s pretty much connected to all smarthome things. I’ve been planning to do this exact same setup! Have a hackrf pro on its way and looking forward to connect it.
Thanks for sharing the .md file.
0
u/frankentriple Aug 09 '26
deepseek v4 flash 0731. That's the model you want to use. Bro's amazing,
And yeah, another Hermes instance runs my HomeAssistant too.
1
u/Chance_Ad5583 Aug 09 '26
Thanks. Running a mixture of Kimi K3, GML 5.2 and Minimax M3 depending on the task. I do like overkill. Will test the deepseek and other models too once I get the device :)
2
u/frankentriple Aug 09 '26
You will use less tokens and get better results with deepseek v4 0731 than you will with kimi 2.5 or minimax m3 (I haven't used kimik3 yet), Glm 5.2 works great but burns tokens like its using them to keep warm. That deepseek model caches so hard it barely burns tokens at all and doesn't go running in loops if you keep it on "medium" reasoning level. Don't go to high, it overthinks things. Medium is perfect.
1
u/808_Sensis Aug 11 '26
Beautiful, now I want to go around and isolate frequencies of dying machines and be I’m here to fix it because it’s calling me.
1
0
Aug 09 '26
[deleted]
4
u/frankentriple Aug 09 '26
I've been in IT for 30 years. I'm not an IT guy any more, I'm a manager. I've worked my way up the ladder from the very bottom of the support ladder to managing a team of devs doing internal SAP integrations for a global company.
I just want the output of the process. A process I control from end to end with the ability to make changes or adjustments anywhere in the chain from one end to the other. I want to be able to apply this process to any input I'd like wihtout constraint.
I'm running a priate fleet of AI agents in my house right now. I'm up to 8 VMs on that proxmox host. And i have an AI monitoring the whole batch so nothing breaks and it all stays updated and keeps track of all the API keys and basically doing all the jobs of a full time sysadmin so I don't have to admin the systems, I can just use them.
1
u/Sidewyz Aug 09 '26
I hear you but people are wired to take the easiest path. We could walk to the corner market, instead we take the car/bus/scooter/skateboard/bike/cat/ebike,etc. I’m guilty, I have AI do mundane tasks as it’s faster and less errors.
0
Aug 09 '26
[deleted]
8
u/frankentriple Aug 09 '26
This guy gets it. I've been doing IT for 30 years. I'm a manager, I do things manager style, I tell my techs to do it and give me the results when they are done. I don't login to servers anymore.
Hermes fits my management/tech style. I know just enough to bump him in the right direction when I know he's off the track. Ask him pointed questions like I do my devs.
I'm not interested in getting down into the technical weeds anymore. I've been doing this since before Google existed. I just want to make it happen, not enjoy the experience along the way, thanks.
2
u/fafnir665 Aug 10 '26
the two guys above me get it lol
Anyone arguing against AI taking the tedious shit off your hands doesn’t get it
1
u/Jonvalt Aug 13 '26
I work in infosec and confidently say most people complaining about AI, vibe coding etc., have no idea what they’re even talking about. On the other hand, same with the tech bros, and the “ai is coming alive” idiots.
1
u/fafnir665 Aug 13 '26
It’s a tool, it is what you make of it.
AI psychosis is real tho, those people are crazy
2
u/throwaway12-ffs Aug 10 '26
It's really not that time consuming and you know it.
0
Aug 10 '26
[deleted]
1
u/throwaway12-ffs Aug 10 '26
Who said you need to do it by hand?
The person YOU replied to suggested that the work of deploying a VM and configuration shouldn't be done by AI and could be done by a few scripts and ansible files. Which I agree. Nobody said by hand. We have automations that dont consume anywhere near the resources of AI.
You're being obtuse for zero reason other than to slob the sloppy knob of AI.
1
8
u/Darqfallen Aug 09 '26
That’s pretty cool. Do you have an instruction set on how you set it all up?