Introduction
Hello everybody, today I wanted to share with you something I’ve tried to do. As you may know, SUN Pharma has let us down considerably in recent months, with more and more people claiming their batches are bad. I’ve experienced these problems myself, with both Modalert and Waklert. Less and less good pills.
So, what I’ve decided to do is to attempt an extraction. I want to do this for two reasons:
Before anyone comments about Adrafinil, I’m really not convinced by it since the considerable stress it puts on the liver, which is really not good in the long term, IMHO.
Also, keep in mind everything in this post comes purely out of my own mind/research, and I’m by no means a chemist, so take everything with a grain of salt. And contribute! If you have anything to say, do it! This post is being written for that exact reason, gain feedback and ideas. This being said, let’s begin!
Theory
To start the research, I went on ecstasydata.org to gain a little bit more informations on what SUN effectively puts into their pills. If you search for ‘Modafinil’, a lot of results come up, with some analysis done in the past few months. In every single Modalert/Waklert pill the only and main substance resulted to be Modafinil/Armodafinil. Good! This already tells us SUN doesn’t put alternate substances in there, but real Modafinil/Armodafinil.
Now the real question was, how much Modafinil/Armodafinil is actually in there? If you know anything about how pressed tablets are made, you know they contain binders or fillers, i.e. substances used to hold the pill together, plus the actual active ingredient. My first guess was that SUN didn’t actually put 200mg/150mg of real Moda/Armoda in every pill, but a variable amount. This could also explain why in the same batch some pills appear to be working while others don’t.
So, how to extract Modafinil/Armodafinil? From this point on, I’ll focus only on Modafinil, since I’ve only researched/attempted that so far. Armodafinil shouldn’t be much different since it’s itself a part of Modafinil.
I went off on Pubchem, to read about Modafinil chemical properties. In the “Chemical and Physical Properties” section, the first thing that caught my attention was the “Solubility“ subsection. Various tests confirm that Modafinil is “practically insoluble in water”. Perfect! This was already a great start, for at least what my high-school chemistry knowledge was telling me.
Now, I had to find what binders/fillers SUN used in their pills. I wasn’t able to find the exact substance (if anyone knows, please do comment!) but found this post here on the subreddit. The comment specifies “lot of companies use lactose as a filling agent - provigil - while most of the indian companies use cellulose products.”. Nice! I read on Wikipedia that cellulose binders are indeed commonly used.
Now, even though I wasn’t able to exactly identify the compound, it’s likely one of these three:
Ethyl Cellulose
E-460(i)
E-460(ii)
These are the most used. Reading up on their chemical properties, I’ve discovered every one of them is also water insoluble. However, I also noticed their molecular weight was considerably greater than that of Modafinil (273.35 g/mol) vs 454.513 g/mol (ethyl cellulose), 36000 g/mol (E-460(i)) and 162000 g/mol!!! (E-460(ii)).
This led me to believe that if dissolved in water, the Modafinil and the binder were going to separate. So I finally had a plan, let’s see it in practice.
Practice
Requirements:
Modalert pill(s)
precision scale
glass (or even better, a beaker)
some container where to crush the pill
something used to crush the pill
water (perhaps distilled water is better, just H2O no other substances present)
a spoon
optionally, a syringe or something to suck up the water later
Procedure:
First, I decided to weigh the pill, just for fun:
Image 1
328 mg, so there should be 200 mg of Modafinil in there plus 128 mg of binder substance, at least theoretically.
Now, what you wanna do is crush up the pill. This is a very important step, and the finer the resulting powder, the better the final result. I used an espresso cup, along with the back of a ladle, was quite large and fit the cup properly. Just mash it for some time, turn it around and keep mashing. Eventually you will end up with something like this:
Image 2
Now, let’s weigh again:
Image 3
35 mg have been lost in the process, some of them stick on the bottom of the cup, some fly away when you’re crushing and some just fall when weighing. Not a big deal, just pay attention to not drop it all!
Now, pour water in the glass/beaker, almost to the top:
Image 4
Then, drop everything in. As soon as the powder touches the water you will already see the separation going on:
Image 5
So, my theory appears to be correct! The stuff that falls down is Modafinil. Now, stir it up for 20-30 seconds, and let it sit for a while (~5-10 minutes). This is how it looks as soon as you stir it and after 5 minutes:
Image 6
Image 7
You can now clearly see the Modafinil at the bottom. The stuff on the surface is the binding chemical. A lot of it will float in the middle before going up, so the longer you let it sit, the better the separation. At this point you can begin to decant. Either pour the water out, being careful not to let the Modafinil mix up again with the water, or suck it up with the syringe.
Either way, this is the end result:
Image 8
Leave just a little bit of water, when you can’t decant anymore without touching the Modafinil. At this point you’ve got two options:
I chose the second one, very low heat, for two minutes until the water was gone. Remember to pick up the glass (with protection, since it gets pretty hot!) every like 10 seconds and give it a twist to stir the remaining water. Modafinil’s melting point is 162 C, so as long as you stay below that and for such a small amount of time it’s no big deal.
When done, you’re left with this:
Image 9
The strange pattern is due to the stirring when heating it up. Now, take the spoon and start scraping it up. That’s your (almost) pure Modafinil! The final yield for this pill was 152 mg, so ~50mg below what it should actually contain (maybe less if you consider what gets lost during the entire process, so this was a pretty good pill!):
Image 10
I’ve tried the process two times on two different pills (same batch, BSR3373) and got respectively 110mg and 150mg. Here’s an upclose of the final result, after scraping off, for this test:
Image 11
The yield was then transferred into a closed container, keep it away from moisture and light.
Testing
Now, the test. I did this whole thing this morning, so tested it in the early afternoon. I “micro dosed” for now, will fully test tomorrow. Took around 25 mg sublingually. The classical shitty Modafinil taste was strong and there, so that’s a good sign (the other powder didn’t have taste!).
Definitely felt the effects, slight stimulation (normal with such a low dose), wakefulness, and the physical effects such as dry mouth increased HR, and the typical sulphur urine. So that is modafinil, and should be pretty pure.
Let me know what you think, particularly if you’ve experience. Is this viable? Is it a shit idea? Let me know!
Thank you for reading until the end!