r/sffpc • u/dan_cases Case Vendor | DAN Cases • Jan 06 '22
Verified Vendor DAN & LianLi A4-H2O - a 11.1l SFF case
19
u/samacunoman Jan 06 '22
Push pin side but still have screws in the back to secure them?
Also, do you have pricing and when is it expected to ship? I understand preorders open Feb 9.
89
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
These screws are optional.
Pricing will be ~ $115 for gen3 and $155 for gen4 riser version.
→ More replies (4)6
u/Hiraganu Jan 07 '22
Why is it so much cheaper compared to the A4?
13
u/duynguyenle Jan 07 '22
If I had to guess, I'd say it's because the new version has had several design elements streamlined and optimised for more economical manufacturing (note the side panels which are all flat, which can be stamped economically as opposed to the old A4 which had curved panels which must be bent in a hydraulic press, the use of an inner steel structure which would have lower base material cost than aluminium). That and the fact that Dancase has been partnering with Lian Li for a long time so they probably have a decent working relationship which is more conductive for rate negotiations etc...
→ More replies (2)9
14
u/Interesting_Ebb1522 Jan 06 '22
I have an MSI 3090 gaming trio, 323mm. How much clearance is there really?
25
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
321-322mm is max but the front is attached with lian li clips so that can give you the missing 1mm.
→ More replies (1)→ More replies (4)4
u/Jesso2k Jan 06 '22
Wondering the same with my 3080. The Gaming X has that stupid tapered point right at the end, I'm betting whatever presses against it will flex.
6
u/jaa5102 Jan 06 '22
That little point is the reason my 3070 Gaming X Trio just barely fit in my Meshlicious.
→ More replies (1)8
13
8
u/digital_noise Jan 06 '22
30mm rad + 25mm fan = 55mm package thickness.
27mm rad + 30mm fan = 57mm package thickness.
Is there any wiggle room with the listed compatibility? I’d love to use my Phanteks fans…
15
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
If you install the pack without the top radiator bracket it will fit but you have to think about securing the rad.
1
3
u/roccatgaming Dec 04 '22
27 mm radiator on top & 30 mm fans mounted underneath the rad work.
You might need to remove the screws securing the fans to the middle part of the radiator.
Make sure the fans rotation is not obstructed when resting against the bracket located at the bottom of the AIO compartment.
8
Jan 06 '22
Damn, I need this. and I need it fast.
What will je RRP be?
With the 3 slot design, it would be possible to leave enough space between motherboard tray and the GPU for the founders edition type of cards correct?
6
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
→ More replies (1)
7
6
6
Jan 07 '22
If you can bring this in below the 200$ mark this thing will sell like hotcakes, hell I might have to find an excuse to tell my wife why I need to build ANOTHER system in this case lmao
19
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
gen3 riser version ~$115
gen4 riser version ~$155
→ More replies (1)
2
u/UnicornsOnLSD Jan 06 '22
How does the graphics card fit in?
3
2
u/raazman Jan 06 '22
Any testing with air cooling for the cpu? I know this is geared toward AIO but would love to have the option to air cool as well.
11
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
It will work as expected. Somethink like a L9a or Blackridge will work like on a open bench table or better because of the possibility to add two 120mm fans in the top area that helps pushing out a lot if hot air, but the cooling Performance will not even close to a 240 AIO.
3
2
u/Aeratus Jan 06 '22
What is the maximum GPU thickness? I'm wondering because 25mm fans on some deshrouds can extend beyond 3 slots.
5
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
5ml for the backplate zone and 60mm for heatsink zone. 65mm in total
2
2
u/DragonApps Jan 07 '22
I remember saying last year that all these new cases that supported 240mm AIO’s, but only 2 slot GPU’s were out of touch with the current market. This really seems like it can be the big case of 2022.
4
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
Yes the current gpu market is very sff unfrindly. Even the dual slot fe cards does not work well with 2 slot sandwich cases but on 3 slot you can do this:
https://www.dan-cases.com/downloads/a4h2o_founders-guide.pdf
2
u/SpringerTheNerd Feb 05 '22
why is there like no coverage of this case? there is only one video on youtube of the finished product. id love to see more of it. it looks to be much more approachable for people who are not super into the SFF life but want a smaller chassis to work with
2
u/dan_cases Case Vendor | DAN Cases Feb 05 '22
7 Feb is official release. There will be more videos on this day
2
2
2
u/rwang40 Feb 14 '22
u/dan_cases - so excited for this case. I meant to buy it but was a day late and pre-order is out of stock now at Newegg. Is there an expected timeline when it'll be available again? I'm in the US so probably Newegg specifically.
1
u/dan_cases Case Vendor | DAN Cases Feb 14 '22
More are in the making :)
Or you order from OverclockersUK
→ More replies (2)
49
Jan 06 '22
Q58 owners be like:
19
Jan 06 '22
I'll stick with my Q58. I like having the 280mm rad in the top.
5
u/tobiascuypers Jan 07 '22
I couldn't fit my GPU in this anyways, I'll stick with my Q58 for a while longer. I love it
→ More replies (11)21
Jan 06 '22 edited Jan 06 '22
Side by side it isn't that much smaller than the q58, it's much thinner but basically the same height and depth.
I considered refunding to wait for this (Newegg holiday return) but that would mean sacrificing an SSD slot and a case fan for a 2cm thinner case. Not worth it for me, I'd much rather have the extra airflow.
→ More replies (2)5
u/mildlynegative Jan 06 '22
Even though I use rear audio, I still want separate headphone/mic on the front and the q58 is combined
Also that case is uglier imo, but I also think the spylabs JOAT is chefs kiss so my opinion may not be valid
29
u/kazolgue Jan 06 '22
Looks really good. And at a nice price. Any updates on the C4-SFX? I'm a fan of air cooling, the C4 would be perfect.
4
Jan 06 '22
C4 already came out right?
11
u/kazolgue Jan 06 '22
No. There was a prototype but last i checked Dan is working on revisions to the design.
https://smallformfactor.net/forum/threads/dan-c4-sfx.12329/page-88
→ More replies (2)2
u/HaoBianTai Jan 07 '22
This was announced at CES 2021 wasn’t it? Looks like the design has changed a lot, is pricing still what they announced last year?
→ More replies (1)2
u/relxp Jan 08 '22
I'm not sure why C4 and A4 even co-exist. They seem so similar in form factor.
9
u/kazolgue Jan 08 '22
https://smallformfactor.net/forum/threads/dan-c4-sfx.12329/page-88
According to the last updates the C4-SFX should be a little bigger and it's a tower design (like the NCase). It's true that they are competing products in the sense that they are both premium sfx cases but at the same time they are significantly different in their internal layout.
49
u/cmh_ender Jan 06 '22
Like a dan a4 and an ncase had a baby. Love it! That should cool a 5900x easy enough!
3
u/KnightGrooves Jan 06 '22
My PC sits to my left on the desk, and would be awesome to be able to use IO easily. Can the panel with the side IO be rotated 180 degrees so that they face the other side?
9
5
3
u/Caspid Jan 07 '22
Yeah, I don't understand people who put their PC on the right. It usually ends up restricting mouse movement too much.
It also messes with the balance: the mouse extends out to the right, so there needs to be something on the left to balance it out.
→ More replies (1)→ More replies (1)2
9
u/CCX-S Jan 06 '22
SFX-L support is nice considering we’re now seeing 450w tdp gpu’s on the horizon
→ More replies (6)4
6
u/VANR_ Jan 06 '22
Can someone with some experience please tell me, how difficult it would be to air cool a CPU (while staying relatively quiet) in a case like this?
I am looking to buy a SFF case with a sandwich layout (3-slot GPU) and really love the look of this one, but I am wondering if I should rather get something a bit bigger, that supports a slightly larger air cooler (like Noctua L12S)?
My current CPU is i7-6700 (non-k), but I might upgrade to something like a i5-12600k or equivalent in the near future.
27
u/DraftyDesert277 Jan 06 '22
BTW Dan is also developing the C4, which I believe will do what you're looking for:
5
u/VANR_ Jan 06 '22
Yeah, I was looking at this case aswell, and it also looks really nice. But I fear my GPU is too tall for this one.. :(
I've got an RTX 2060 Ventus from MSI, with dimensions of 226 x 128 x 41 mm. Assuming CPU height limitations apply to GPUs aswell, C4's 130mm probably arent sufficient for me to fit this GPU in, right?
→ More replies (2)→ More replies (1)23
u/DraftyDesert277 Jan 06 '22
This case is very explicitly designed for water cooling. There are a million sff cases that do air cooling better, and that's intentional. I don't want to speak for Dan, but I suspect that's why it has H2O in the name... 😉
9
u/Aeratus Jan 06 '22
Actually, there aren't that many air cooling cases that fit a 3 slot GPU (>60mm) in 11 liters. There are only a few, such as the SM560.
→ More replies (1)
2
u/TheRealGlutenbob Jan 06 '22
Looks amazing! Any thermal testing data?
9
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
In Chinebench multithread infinity loop + ValleyBench infinity loop running at the same time i got:
EKWB 240 AIO + 2x Noctua A12x25
Ryzen 3900X = 77°C RTX 3080 FE = 75°C
→ More replies (8)1
u/thetrillchailover Jan 16 '22
Thread is a few days old now but if you read this I would appreciate some feedback when you get a chance. During testing was the 3080 used with stock setting and not an undervolted/underclocked card? Thanks. Great looking case. Will be patiently waiting to pre-order this in a couple weeks.
3
9
Jan 06 '22
Time to upgrade from the A4 SFX it seems ! I don't really care for the 3 slot GPU room though 🤔
→ More replies (4)55
u/DraftyDesert277 Jan 06 '22
Reality is most mainstream cards now require at least 2.5 compatibility. Dan didn't have a choice here.
7
Jan 06 '22
Yea that's true. I guess that's the future proof move.
31
u/DraftyDesert277 Jan 06 '22
Yup. Well, really present proof haha, there's just no way around it at this point.
I say this as someone who has an original A4 and really wanted a 3080 xc, but was "only" able to get the ultra and as such had to move to a new case.
This is a day-1 purchase for me!
→ More replies (7)
4
4
4
Jan 06 '22
I think I’ll be all over this. My wife needs a rebuild!
21
1
u/Caspid Jan 07 '22
What's the difference between this and the C4? Is that still coming out?
3
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
C4 is bigger. Has 280rad support and does use a classic hardware layout instead 8f a sandwich layout
1
1
1
u/crrLarson Jan 06 '22
Where can I buy this
4
1
Jan 06 '22
How much will it cost?
7
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
Gen3 riser version ~$115
Gen4 riser version ~$155
→ More replies (1)
1
1
u/SupaDiogenes Jan 06 '22
Will this ever make it to the southern hemisphere? Having pre-orders available from places we can't really access makes me think stock is going to be tied up with Europe and the US.
→ More replies (2)3
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
Yes later in Q1 it will be available on all LianLi partner stores.
1
u/slimejumper Jan 06 '22
bit of not-very-important feedback, the pdf manual currently writes H2O with a superscript rather than a subscript on the 2.
The case looks great, i’m very tempted to swap from my meshlicious to this so i can have rear gpu outputs.
3
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
Yes i know. Manuals are already printed so i will change that for the next batch.
→ More replies (1)
1
1
u/dmfguk Jan 06 '22
This looks absolutely stunning! Is a full custom loop (CPU and GPU) going to be feasible in this case? It looks like it might be hard to get a tube across the sandwich divider?
2
1
1
u/relxp Jan 06 '22
How compatible is this with blow through/FE cards?
3
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
1
1
u/Ziakel Jan 07 '22
Is there a gpu height limit? I got a 3080ti ftw3
1
1
Jan 07 '22
u/dan-cases, The Optimum Tech review was quoted as saying that GPU thickness should not exceed 50mm which isn't that close to 3 slot thickness, is this outdated information on their part?
1
1
u/ayylmao_jpg1 Jan 07 '22
As someone who doesn't use front io, will there be an option to swap out the front io to only have the power button like the ncase? It minimize cable clutter inside and having to connect yet another cable to the motherboard
2
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
Sry this isnt possible but you place the case on the left side of your table. Then you will see no io ports.
1
1
u/BJozi Jan 07 '22
This is very like how I remember the C4 which then for a complete make over. How does this compare to the original a4, is it much larger?
Very nice case sir!
2
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
A4-SFX is 115x200x317mm (WxHxD) = 7.2l A4-H2O is 140x244x326mm (WxHxD) = 11.1l
→ More replies (1)
1
1
u/AnAnonymousMoose Jan 07 '22
Is there a way to have no front I/O slots at all?
10
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
Move the case to the left side of your table and you will not see it.
6
1
u/thetrillchailover Jan 07 '22
How would an FE GPU do here? I heard they don’t do great in sandwich layout. Thanks.
2
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
This is true for sandwich style cases with a 2 slot chamber. The back fan of a founders will work very close against a solid wall (the psu) so it can move as much air as needed. On a 3 Slot sandwich case you can do this:
https://www.dan-cases.com/downloads/a4h2o_founders-guide.pdf
This will result in enough space between psu and founders back fan. The AIO fans helps to push that hot air out.
→ More replies (3)
1
u/ProperNorf Jan 07 '22
Will it fit the 3090 FE ?
2
u/dan_cases Case Vendor | DAN Cases Jan 07 '22
Yes but the back fan will not be able to work on max efficincy because it is very close to the psu. On a dual slot founders like 3080 ti you can do this:
https://www.dan-cases.com/downloads/a4h2o_founders-guide.pdf
1
u/KidFiasco Jan 11 '22
Will it fit a 3090 FE and will this case be available in canada?
1
u/dan_cases Case Vendor | DAN Cases Jan 11 '22
Fit yes but not perform well because of its design.
1
u/KidFiasco Jan 11 '22
Expected thermals ?
1
u/dan_cases Case Vendor | DAN Cases Jan 11 '22
The back fan will push agsinst a solid wall. Its like a 3080fe in a dual slot sandwich.
1
u/TheRealGlutenbob Jan 11 '22
In your first picture, is that the optimal orientation for that AIO? I plan on buying the 240 Basic, but the tube lengths should be the same.
2
u/dan_cases Case Vendor | DAN Cases Jan 11 '22
Tubes comes out on the left with tubes go down around the pump and than up is my favorite for the EKWB.
→ More replies (1)
1
u/Gruebi Jan 12 '22
What is the maximum rad size? Optimum Tech mentioned NZXT Kraken does not fit
3
u/dan_cases Case Vendor | DAN Cases Jan 13 '22
Optimum made a preview on the first prototype. We redesigned the product now you can fit rads up to 133x280x30 (WxLxH)
1
u/Gruebi Jan 13 '22
And how about Arctics Liquid Freezer? I guess there‘s not enough clearance for the tubes to come straight up am I right?
3
u/dan_cases Case Vendor | DAN Cases Jan 13 '22
Max pump height is 55mm so thr Artic will not fit because with tubes it requires 70-80mm
1
1
1
u/Patrick22492 Jan 15 '22
What would the best fan config if I’m running an aio loop? 2 at the top on pull or push?
1
u/dan_cases Case Vendor | DAN Cases Jan 15 '22
Radiator on top fan below. Fan pull inside the case and push through the radiator.
1
u/Strooble Jan 15 '22
What is the CPU cooler here? It looks so nice!
2
u/dan_cases Case Vendor | DAN Cases Jan 15 '22
→ More replies (1)
1
u/CCX-S Jan 18 '22
Any chance of white rather than black/silver?
2
u/dan_cases Case Vendor | DAN Cases Jan 18 '22
Maybe later
2
u/CCX-S Jan 18 '22
All the colored panels are removable, yes? If so then one could always panel swap down the track if a new color became available, at least in theory?
3
1
u/bigmedley Jan 21 '22
is it made in Taiwan or made in China?
→ More replies (1)2
u/dan_cases Case Vendor | DAN Cases Jan 21 '22
This one is made in China. Taiwan is only for smaller batches like M1 or A4-SFX. China factory is for mass production
1
1
1
u/aexeq Feb 09 '22
Hey Dan, when will Caseking have the case listet for pre order today? Since it's a worldwide drop, I guess around afternoon in Germany?
→ More replies (2)2
1
u/chrisduncan_2323 Feb 09 '22
Anyone think a 3099 fe will fit in this thing?
2
u/dan_cases Case Vendor | DAN Cases Feb 09 '22
It will fit but will not work propper because back fan is blocked by psu.
→ More replies (1)
1
u/uncertain-host Feb 10 '22
u/dan_cases will a MSI 3070 gaming z trio fit?
1
u/dan_cases Case Vendor | DAN Cases Feb 10 '22
We never tested it. But the front clips allowes for 0.5mm movement so maybe yes. But from the pure facts it is 1mm too long.
1
u/subject19 Feb 11 '22
I have a 5600x and a 3080 TUF and am leaning towards a 120 AIO and A12x25 as exhaust for better GPU thermals. Will this work or should I stick to a 240?
2
1
Mar 03 '22
Any approximations on availability? Been refreshing newegg but it never went in stock.
1
u/dan_cases Case Vendor | DAN Cases Mar 04 '22
It was on launch day. The demand was very high so it sold out in a day. New cases are in the making.
1
1
u/Additional_Dirt_7289 Mar 17 '22
Would it be possible to mount 92x15 fan below the psu instead of SSD? Old A4 style? Or perhaps even an 120x15 intake on top of EK 240 CPU block?
1
1
u/Xertiem May 02 '22
This might be a silly question, but if the DAN & LianLi A4-H2O can fit a 2.5” SSD drive (mention in their official website), would it be possible to add one (or 2) fans in to the bottom panel?
If so, what size would be compatible (dimensions) and how many (1 or 2)?
Just trying to think if it's possible to increase the airflow.
1
1
Sep 09 '22
Has anyone gotten an MSI RTX30x Gaming X Trio to fit in one of these? I'd rather not try and find out the expensive/hard way.
1
u/kanth1991 Oct 24 '22
can holes be drilled on the top where your logo is ( sorry ) to use an external radiator without ofc using Radiator or Fans within the case itself ?
2
1
2
2
2
2
u/Signaturisti Jan 07 '22 edited Jan 07 '22
In my opinion that side panel front I/O cutout resembles Sliger SM-series cases too much.
Otherwise much cleaner design tho!
2
u/KimChi3f Feb 08 '22
Would the Phanteks T30 fans fit in this case?
3
u/MetroMetroid Feb 09 '22
need this answer too. going down to a 240mm from a 280 so im hoping not to lose much cooling performance
2
3
u/kazolgue Jan 06 '22
Looks really good. And at a nice price. Any updates on the C4-SFX? I'm a fan of air cooling, the C4 would be perfect.






192
u/dan_cases Case Vendor | DAN Cases Jan 06 '22
The A4-H2O or chemical correct A4-H₂O was designed by DAN Cases GmbH and will be sold by LianLi Ltd. The result is a true SFF product, with DAN dna, LianLi quality, a fair price and good availability - "a tribute to SFF".
In 11 liter this case fits a 3-slot GPU with an length up to 321mm, a 240 AIO with standard fans and can handle high TDP CPUs like the 12700k. This case is perfect for SFF (Small Form Factor) enthusiasts, those who need a highly portable system, developers who require a case with a smaller footprint due to limited desk space, and gamers who want a high-end PC experience in their living room.
Case Dimensions (H x W x D): 244 x 140 x 326mm, 11,1L
Graphic cards support: 3 Slot GPU up to 322mm length
Motherboard support: Mini-ITX
Power Supply support: SFX, SFX-L
Water cooling support: up to 240mm radiator (30mm thick) with 120x120x25mm fans
Drives: up to 1 x 2.5" HDD/SSD
IO: USB-A, Audio, Mic, USB-C
Power button: Premium-grade button
Material: 1.5-2mm aluminum (outer panels), 1.5mm steel (inner parts)
Side panels: Easily clipp able with LianLi Push Pin technology
Colors: Anodized black(maybe dark grey) or silver exterior, matte black painted interior
Risercard: PCIe 16x gen4 or gen3
Release: Preorders on 9th Feb 2022 (Caseking; Newegg & OCUK)